Cisco vtp client not updating

posted by | Leave a comment

This is a good security measure as well as a way to prevent accidentally adding a wrong or misconfigured switch to the VTP domain.You can look at the VTP status/information of a switch with the “show vtp status’ command as shown below on the VTP server switch, ‘Cisco_Nexus5548UP_1′.I've tried sh vtp status VTP Version capable : 1 to 3 VTP version running : 2 VTP Domain Name : abx VTP Pruning Mode : Disabled VTP Traps Generation : Disabled Device ID : 001b.d468.1e80 Configuration last modified by XX. XX.64.199 on interface Vl5 (lowest numbered VLAN interface found) Feature VLAN: -------------- VTP Operating Mode : Server Maximum VLANs supported locally : 1005 Number of existing VLANs : 51 Configuration Revision : 3 MD5 digest : 0x B4 0x14 0x13 0x58 0x4A 0x BD 0x2E 0x D3 0x1E 0x0E 0x76 0x73 0x DA 0x D3 0x BB 0x33 sh vtp status VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 254 Number of existing VLANs : 49 VTP Operating Mode : Client VTP Domain Name : abx VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x38 0x FA 0x7A 0x8A 0x21 0x2E 0x98 0x2A Configuration last modified by XX.XX.64.199 at 12-26-13 interface Fast Ethernet1/0/47 description Crossover to 9.12 switchport trunk encapsulation dot1q switchport mode trunk sh int fa1/0/47 trunk Port Mode Encapsulation Status Native vlan Fa1/0/47 on 802.1q trunking 1 Port Vlans allowed on trunk Fa1/0/47 1-4094 Port Vlans allowed and active in management domain Fa1/0/47 1-2,5-6,8-9,11,17,22,25-27,30-31,34-35,38,43,46-47,49-50,52,55,57,60,62,68,71-72,74,77-78,93-95,105,112,118,202,227-229,233-234,262,520,907 Port Vlans in spanning tree forwarding state and not pruned Fa1/0/47 1-2,5-6,8-9,11,17,22,25-27,30-31,34-35,38,43,46-47,49-50,52,55,57,60,62,68,71-72,74,77-78,93-95,105,112,118,202,227-229,233-234,262,520,907 It turns out that the Client switches had a VTP Password set.Hope this helps someone out there that ran into this similar situation.Good day all, I have some quick questions in regards to VTP client to transparent.

Despite the fact Profilic clearly states that these chipset are not supported with the latest Windows, forcing users to purchase new adapters powered by their new chipsets, we’ve proven that this is not true and showed how to make the old Profilic USB-to-Serial adapter work with the drivers available on In this blog, I’ll demonstrate how to utilize Cisco’s VLAN Trunking Protocol (VTP) to manage VLANs across a network.

Select Let me pick from a list of device drivers on my computer Next, select the driver version 3.3.2.102 dated 24/09/2008 as shown below and click Next: Figure 6.

Install Driver version 3.3.2.102 Once complete, Windows will confirm the successful installation of our driver as shown below: Figure 7.

after searching and coming across this discussion I found that the client switch had a VTP password set while the server did not.

This "2nd switch", the client was from another office and added to this office with only the one switch.

Leave a Reply

ferne go dating